Month: February 2019

Hybrid Cars- A Revolution In The Car Industry

blogger /

Hybrid cars are one of the excellent fruits of the hard work done in the car industry. These cars utilise more than two distinct power sources. Some of the major power sources include gasoline, or diesel fuels, solar, and hydrogen. This primary power source is coupled with one, or more electric motors.

World is facing a lot ofmany problems due to the increased population. There is a rapid increase in the number of vehicles along the roads. This has given rise to the pollution, and problems related to the increased fuel prices. This problem is addressed by the great minds, by inventing the hybrid cars.

These cars are a revolution in the car industry due to their marvellous features. These cars are environment friendly. They contribute least to the increase in the air pollution. Air pollution is one of the major problems of the present day. Hybrid cars reduce the smog by 90 percent. Thus, the release of the pollutant is greatly reduced.

Hybrid cars are economical with respect to the fuel. World is running out of the natural fuel resources. , Soso the need of the fuel economical vehicles is greatly increased. They are fuel efficient as compare to the traditional cars. They can get up to 60 miles per gallon in the city driving as compare to the typical cars that might travel 15 to 20 miles per gallon. These cars use three times as much fuel for travelling the same distance. The hybrid cars are better than others as a hybrid car battery recharges it as you drive. You do ntnot need to plug in. Moreover, they possess a greater speed as compare to the typical cars.

Hybrid cars possess two engines. One is the electric motor, and the other is the gasoline. When the car stops at the signals, the gasoline engine is automatically shut off and the electric motor is switched on. When more power is required, both engines work simultaneously.

Hybrid cars are based on power split technology. It is based on the gearbox. The electric motor along with the internal combustion engine provides additional power to assist the engine in accelerating, passing, or climbing. In some of the drives, where less power is required, the motor provides the only power source. Thus, the consumption of gasoline is reduced in such cases.

Hybrid cars possess an efficient regenerative braking system. When the brakes are applied, the energy is dissipated. This energy turns on the motor, which functions as the generator. Thus, the otherwise wasted energy is converted into electricity. This energy is stored in the battery, and is available for the electric motor.

Hybrid cars have firm and puffed up tires. They are filled at a higher pressure to smoothen the ride. So due to the texture, they offer a less bumpy, and comfortable ride. The texture of the tires reduce the friction, thus the life of the tire is increased. The other marvellous feature of the car is reduced air drag . For this purpose, these cars utilise the reduced frontal area, and sometimes a stream lined texture. Thus, all the above- mentioned features rank their invention a revolutionary step in the vehicle industry.

Rapid Prototype Mold Industry Outlook And Trend Analysis

blogger /

In recent years, steady and rapid economic development, stimulating rapid growth in fixed assets investment, China Mould market demand. As the industry improve its competitiveness and national policy support, domestic rapid prototype Shenzhen mold industry output value and sales revenue for many years to maintain the growth rate of 20%. Die Network CEO, Shenzhen Institute of Deputy Secretary-General Luo Baihui mold technology recently introduced to the Dongguan Daily News the latest developments in the mold industry.

1, mold development prospects of the industry

1, mold market prospects in China

Mold applications continues to expand, the field has been applied to the mold that the larger and higher demand of industrial development to mold faster than the speed of development of other manufacturing industries has become a universal law, mold the world market demand, in recent years, the market total has been between 600 ~ 65 billion U.S. dollars, while China’s export was not mold to 8%, “during” can expand this share, and with the development trend of economic globalization has become more evident, mold manufacturing industry gradually China and the multinational corporations to transfer mold our country has become more evident towards the procurement of foreign and private capital to continue to favor China’s mold industry, China’s mold industry more opportunities than challenges, the future market prospects of international mold, China mold is still large room for development.

2, mold product market and increase their competitiveness

At present, China is facing the technological advantages of the developed countries and developing countries, the dual pressures of price advantage. Industrial countries die with its technological and business strengths, in the high-end molds a competitive advantage, as they are gradually entering the country, the mold industry in China becomes a tremendous challenge; India, Thailand and Eastern European countries in recent years, industrial mold developed very rapidly and the price of its mold also has a strong competitive advantage, China’s mold industry, the cost and price advantage will gradually weaken and eventually disappear. Luobai Hui said that China must die enterprises technology, management and personnel training efforts, and actively introducing foreign advanced mold manufacturing technology to enhance the ability of high-end product development die, adjusting product structure mold, mold products, continuously improve our international competitiveness.

3, mold growth rate of industry

China’s national economy in the “Eleventh Five-Year” period will continue to maintain relatively fast growth rate, to the mold industry, the development of a reliable macro support. Automotive, IT, electronic information, household appliances, OA office equipment, machinery and building materials industry, aerospace, mold needs are large power tools, home appliances and electronic information industries only example of a refrigerator Xu Yong mold about 150 parts , requiring a total of about 350 sets of molds; a need for automatic washing machine more than 150 sets of molds; one air conditioner, only to be 20 sets of plastic mold; die each model takes more than 30 sets of computers, along with its matching printer need to die more than 20 single deputy; also notebook computer, the network will have tens of millions of units set-top box market. As much as the current models developed abroad, mold import more, as China developed its own capabilities in this regard will be greatly increased demand for mold. China’s mold industry can be expected in a good macro environment of rapid development.

4, mold industry opportunities and challenges

On the one hand for the mold industry, domestic and international situation provides an unprecedented development in the development of space, while the other mold will also face more intense competitive challenges, in addition to international competition, at home, Xiaoshan, Shanghai and Shenzhen, will develop mold industries, such as Xiaoshan You into the mold company’s annual sales revenue reached 2 billion, as Friends of the Japanese professional mold factory mechanic’s wholly-owned enterprises, mainly engaged in automotive and appliance dies production, is currently being planned for the support of Xiaoshan City Hong Kong GEM; Huangyan mold industry in management, equipment, technology has also been taking the forefront in the province; mold more than 30 million annual production value of Wenzhou City, is preparing the further development of the mold industry, the five leading enterprise jointly set up mold Constant Field mold company 200 million yuan investment mold built based technology centers were the focus of government support; once the dominant player in the country mold industry in Shanghai, want to revive the former glory of the Shanghai Municipal Economic Commission, the main control center is in full swing mold to build an area of 1,500 acres, modern industrial park will soon die show in front of people; Suzhou New District proposed building a high level with international standards of modern industrial base mold the idea of an area of 2,000 acres ; South China University and the Guangdong Fonda Group signed an agreement, prepared to die city of Changan Town, Dongguan City, played an important cause of mold in southern China R & D base; Shenzhen City in the industrial structure adjustment, the clear will die as the head of the advanced manufacturing industry, investment about 6 billion yuan industrial park building mold; invest 5 billion yuan in Chongqing to build China’s largest, highest standard of automobile, motorcycle mold industrial park, planned in 2035, the annual output value of 3.0 billion; Shantou Plastic Machinery Mould total annual output value of over 10 billion yuan, currently about plastics, machinery and related tooling enterprises with 3,000, most of the companies complete the introduction of Germany, France, Italy and Taiwan, the region’s new CNC mold processing equipment, greatly improved product performance and quality grade . There are a number of other provinces and cities in China (Nanchang, Jiangxi, Shaanxi, Xi’an, Dalian, Yantai, Shandong, Hebei Botou) have to seize our country is becoming a “world factory” great opportunity to create molds Park, brewing industry further escalation of the mold.

Second, analysis of industry trends mold

1, mold market globalization, the mold further reduce the production cycle

Mold the globalization of markets is the most important features of today’s mold industry is one of the mold buyers and manufacturers all over the world, the globalization of the development of tooling industry to the production process is simple, low precision mold processing enterprises to the technology is relatively backward in productivity than Countries with low migration, mold manufacturing enterprises in developed countries are located in the production of high levels of mold, mold manufacturing enterprises have to face global competition, manufacturers have to die while doing everything possible to speed up the production progress, efforts to simplify and abolishes necessary to the production process, the mold production cycle will be further reduced.

2, Die CAD / CAM to the integration, intelligence, and network development

More complete software modules, while the function module using the same data model and implement integrated management and sharing of information, support mold design, manufacturing, assembly, inspection, testing and production management of the entire process. Some series software includes a surface / solid geometric modeling, engineering drawing complex geometry, advanced rendering industrial design, mold design expert system, complex physical CAM, artistic design and sculpture automatic programming system, reverse engineering system and the complex physical-line measurement system ; mold design, analysis, manufacturing three-dimensional technology, paperless new generation of software to three-dimensional mold, intuitive sense to design the mold, using three-dimensional digital model can be easily used in the product structure of the CAE analysis, mold can produce evaluation and CNC machining, forming process simulation and information management and sharing; the same time as competition, cooperation, production and management of globalization and internationalization, and rapid development of computer hardware and software technology, network Shide Zai die industry virtual design, agile manufacturing technology both necessary and possible.

3, mold technology to high speed machining, hard milling and compound machining direction

With the precision mold to develop in the direction of and large, ultra-precision finishing technology over 1m and collector, chemical, ultrasonic, laser processing technology integrated with the composite mold in the future will have broad prospects. High-speed machining to the workpiece surface was smooth, save processing time, typically only a step away from 0.0254mm, and sharp point only 0.001mm high, after the majority of high-speed machining of the workpiece surface is very smooth, no fitter further processing. Currently, machine tool manufacturers are keen on the production process and the specially designed high-speed machining center, high-speed processing technology in the United States to reduce or eliminate fitter process is a considerable efficiency measures, this technology in Europe and Japan popular. In addition, hardening of the material processing with a full mold cavity mold processing industry is another important trend. High spindle speed and a small tool radius cutting carried out by the formation of mildly enough torque, can be used to process up to 64HRC hardness of metal materials, because no need for heat treatment, conventional heat treatment and tempering after the offset caused by the heat treatment carried out by the geometric deformation of grinding also do not need, and the technology in Japan, the acclaimed, now in the United States has also been a lot of attention and positive spread in Europe.

With the rapid development of new technologies, foreign countries have emerged mold automatic processing system that the rational combination of multiple machines, with accompanying positioning fixture or positioning disk, a complete equipment, tools and CNC numerical control database synchronization system of flexible with real-time quality monitoring and control system.

4, mold will be large, precision, standardization direction

On the one hand increasingly large part of molding and to improve production efficiency development of “a multi-cavity mold,” led to mold growing large, the other electronic information industry, medicine, rapid development has brought parts of miniaturization and precision, some tolerance precision mold requires less in the 1m. Another multi-functional composite mold will develop further, in addition to the new multi-functional composite mold Stamping parts, also responsible for layers, tapping, riveting and assembly tasks such as locking, to further improve production efficiency.

Mold standard parts used in developed countries generally cover about 80%, as China’s mold industry, mold will enhance standardization, standardization will be further enhanced mold, mold standard parts of the application and production in the “Eleventh Five-Year” will be greater during the development.

5, the hot runner mold species, mold and adapt to the high-pressure gas-assisted injection molding direction

Mold with hot runner technology can improve productivity and quality of workpiece, and can produce significant savings of raw materials, many foreign plastic mold factory produced more than 50% of plastic molds using hot runner technology, and some have more than 80% The effect is obvious; Gas-assisted injection molding with injection pressure is low, Warpage small, good surface quality and easy-to-wall forming larger products, such as differences in advantages in the premise of ensuring product quality and substantially reduce costs; high-pressure injection molding of resin shrinkage can be forced to increase the dimensional stability of plastic parts; another injection compression molding technology, enables forming a small piece of local internal strain can be less thick Molding shrinkage, while the narrow components for plastic parts can also be injected resin, and used a small injection of power to get good products, these technologies are gradually promoting the use of.

6, very broad prospects for rapid economic mold

Many varieties of small batch production era, people asked mold production cycle as short as possible, so rapid economic development of mold will have broad prospects. Expected in the 21st century, with various superplastic materials to produce molds with epoxy, polyester, or in which the filler metal and glass reinforcement and making simple molds and other production means the ratio of total industrial production will reach 75%. Rapid economic mold include rapid prototyping, surface forming tooling, casting forming tooling, extrusion mold technology and ultra-molded shape, multi-point forming technology, KEVRON steel blanking blanking tooling , mold blank rapid manufacturing technology.

7, high-quality mold materials and advanced surface treatment technology attention

Due to improper selection and use of materials, causing premature die failure, which accounts for more than 45% failure die, so choose the appropriate application of high-quality steel and surface treatment technologies to improve the life of the mold is very important to improve the purity of steel, isotropic , the density and uniformity, and development of more high-performance or performance of a special mold steel, mold steel specifications development, expansion of other high-quality mold materials such as carbide, ceramic materials, composite materials, the application of such a major research focus; use aluminum alloy for mold materials to shorten the molding cycle, reducing die costs, will be faster in the rapid economic development of mold.

Mold surface is the main trends: the infiltration of a single element to the multi-element penetration, complex permeability development, from the general diffusion to CVD, PVD, PCVD, ion penetration, the direction of ion implantation, etc., can be used in the coating are: TiC, TiN, TiCN, TiAlN, CrN, Cr7C3, W2C, etc., while heat means heat from the atmosphere to the development of vacuum heat treatment. Currently laser strengthening, glow plasma nitriding and electroplating (plating) enhanced anti-corrosion technologies are also more and more attention.

8, auto, IT development impact the electronics industry market sentiment dies

China imported the first negative mold growth, mold industry by the “one large and one small” pull, the development of really good the last two years. “A major” refers to the automotive industry, automobile industry refers to not only vehicle, as well as automotive components, such as the United States at present in China for the first time the second largest auto parts exporter, which means that China’s auto mold market has played an irreplaceable role. Its rapid development of mold plays an important role in driving, “a small” refers to the IT electronics industry. Die in 2006 for the 2.047 billion U.S. dollars of total imports, 2.068 billion U.S. dollars in 2005 reduced the 21 million U.S. dollars, for the first time negative growth, stopped the momentum of the expansion of imports increased every year; exports totaled 1.041 billion U.S. dollars, more than an increase of 41.06 percent in 2005, for the first time over 10 billion dollars and imports to reduce the deficit down, is very gratifying.

9, the mold need to further adjust the industrial structure

Although the mold industry and previous years has made significant progress, but there are still many problems. For example, the phenomenon of irrational industrial structure still exist. Structure, including product mix, technological structure, import and export structures, there are different degrees of problems. For example, in the import and export structure, due to the mold design and manufacturing standards and capabilities can not meet the market demand, therefore, die every year a large number of imports, especially high-end products. In 2006 the import and export stamping die, if by weight, priced at 14,913 U.S. dollars / t, and 5,869 U.S. dollars / t, much higher than the import export; while for plastic rubber mold, in 2006 imports and exports were 413,715 units and 1,217,772 units, exports is far greater than imports, while the unit is very different from the poor: the import price of 2532 U.S. dollars / set, the export price 602 U.S. dollars / set, a difference of four times, although the export volume was nearly 3 times the amount of imports, but still below the total amount of imports . That we are still importing large quantities of high quality molds, exports are dominated by middle and low. Therefore, in the long run, the rationalization of import and export trends should be expanded exports and reduce imports, making exports more than imports. Obviously, this also needs to want to be a period of time.

10 management companies restrict the development of mold

Unlike mold manufacturing process management product management, it is the face of unit production of the mold industry, and how digital information management, is very learned. If the mold is not a scientific management, dynamic management approach, we can not guarantee orderly mold manufacturing, rapid prototype Shenzhen mold supplier in time. Meanwhile, each company’s mold products are different, so they need individual management. Those who do well die business, they have a set of unique, for their own management, but that too few companies. Luobai Hui pointed out that the mold business if we do not focus on management development will not continue, and this has seriously constrained the mold enterprise development bottlenecks.

Jobs in the Music Industry

blogger /

Everyone loves to be a part of the “in” crowd and lets face it yall. Being in the music industry is about as “in” as it gets. Most of the jobs in the music industry put you close, at least in some way, shape or form with the people that your peers consider to be icons and a hero.

There is nothing finer than actually making money at a job that you actually love as opposed to standing on an assembly line watching the same part go by hour after day after year.

Jobs in the music industry can range from the retail sales ends, to the production end, to the creative department to performing or the business end and there is a lot of jobs in between those stops. There is a good chance that no matter what it is you like to do, there is a job in the music industry that will allow you to do some form of that job and eventually get paid to do it.

You need to seek out jobs in the music industry at local places and you can check the World Wide Web at locations like myMusicCircle and see what kinds of jobs are there that you can start at right away so that you can begin building and diversifying your skill set. Because the music business is first and foremost, a business and that means that the more skills you have the more valuable you will be. And we all know that the more valuable you are the more invaluable you become and the easier it is to find the jobs that you ultimately want.

If your end goal is to be a producer, you can start by offering to mix local bands live at their show for free or beer. Youll get the basic skills and then move one. A lot of what you might do at the beginning is mundane and wont pay you very well if at all. You need to keep you eye on the brass ring and the goal that you have set.

Many of the people that are very huge icons in the industry got their first jobs in the music industry doing things like taking out the trash at a studio or helping as a gaffer that set up for the sessions. All of this is networking and making contacts of people that can help you or hurt you down the line.

Overview Of Indian Tyre Industry

blogger /

The Rs.20, 000 crore Indian Tyre Industry, is highly raw material intensive and predominantly a Cross Ply (or Bias) tyre manufacturing industry. It produces all categories of tyres, except Snow Tyres and Aero Tyre for which there is no demand domestically. Indian tyre industry is highly concentrated wherein 10 large manufacturers account for over 95% of the total tonnage production of 11.35 lakh M.T. On an average, 55% of the production is for replacement market, followed by 29.8% sold to OEMs directly and the remaining is exported.

Over the years, tyre manufacturers have developed a vast marketing network using dealers and depots and as such all types of tyres are now easily available even in the remotest corner of the country. No doubt, international auto majors in India now roll out their vehicles using Indian manufactured tyres.

Slowdown in automotive industry and global economic in general negatively impacted the Indian tyre industry in 2009. The industry tonnage growth was only 2.19% during first nine months of FY09, compared to 7.38% growth experienced during the same period last year. Demand side was also severely affected as almost all auto manufacturers were forced to adjust their production last year. A major relief for tyre manufacturers was provided by the government by reducing the excise duty on tyres from 14% to 10% in December 2008, and further to 8% in February 2009.

Increasing Cost of Raw Materials: Ram materials primarily comprise of natural rubber, crude and steel based materials which have historically experienced volatility in prices, especially during the last few months when price of domestic natural rubber increased almost 40%. Given the fact that raw materials constitute around 70% of the cost of production, combined with the manufacturers” inability to pass on the increased cost to their customers due to intense competition, rise in prices of these materials have a huge impact on profitability.

Increasing Radialization: Unlike in the developed countries, radialization has not yet reached its dominance in India. Particularly the truck, bus and LCV segments continue to be largely a cross ply based. Despite offering higher mileage, lower fuel consumption and improved safety, radial tyres have not yet caught on primarily because of poor road conditions and high initial cost which is approximately 25% higher than bias tyres. Moreover, the two important raw materials required for producing radial tyres (Steel Tyre Cord and Polyester Tyre Cord) are not manufactured domestically. Moving towards radialization will be vital if tyre producers want to protect their share in international markets. As of 2008, radialization as a percent of total production in passenger car tyres, LCV and heavy vehicles was 95%, 12% and 3% respectively.

Off the Road Tyres: Last year saw the top manufacturers, including CEAT and JK Tyres increasing their capacity of OTR (Off the Road) tyre production. OTR tyres are customized tyres and provide relatively higher margin. Increasing the proportion of OTR in the product mix is seen as a measure to improve profitability.

Increased Dumping: Besides material price fluctuations and lack of radialization, the industry is also suffering intense competition from low priced tyres from China and other South East Asian countries. Despite being of a better quality, Indian manufactured tyres loose ground when it comes to pricing. Moreover, slowing automotive demand from developed countries has made India a lucrative market for cheap tyres, thus resulting in increased dumping of cheap tyres from China.

Retreading: Another area of concern for the tyre manufacturers is the increasing retreading, where the worn out tread of the old tyre is replaced with a new tread. Retreading costs approximately 20% of a new tyre and is therefore gaining popularity, especially in Southern part of the country. Elgi Tyres and Tread Ltd are the two major retreaders in India. Significance of such retreaders can be gauged by the fact that around 85% of the tyre demand is for replacement.

Unresolved Tax Issue: The issue of inverted tax structure, wherein the import duty on natural rubber is 20% but import duty on finished tyres is as low as 10% still remains unaddressed. Operational inefficiency and taxation issues have being denting the competitiveness of Indian tyres.

Global Expansion: Several manufacturers are now moving global and are setting up manufacturing bases overseas. After acquiring Dunlop three years ago, Apollo Tyres recently acquired Vredetein Banden in Europe. JK Tyres acquired Tornel, a Mexican company last year to penetrate into American tyre market.

Despite these challenges, according to CARE Research, while the industry may register a tonnage growth of only 4.27% in FY09, the long term prospective seems to be bright. They expect the industry to experience a CAGR of approximately 8.21% between FY08 to FY13. Automotive companies have started experiencing increasing sales and raw material prices are stabilizing which will boost tyre sales over the coming months. However, experts suggest there will be some time lag before profitability picks up as tyre manufacturers are still carrying high cost inventories.

Direct Response Advertising – The Multi Billion Dollar Industry

blogger /

Direct Response Advertising is an up and coming industry worth over 250 Billion Dollars. The funny thing about it is that consumers dont generally feel like they are affected by it. Believing that they arent gullible enough to fool for an advertising campaign. This is until you find they own a Smeg fridge and the latest HD TV. Even people who are suspicious of advertising find a way of being sold things that they might not normally purchase and this is why Direct Response Advertising is such a massive industry.

This form of advertising is easily the most effective form being used today, why is this? One word. Television. Experts in America believe that companies can put their brand across to over 98% of the population. That is approximately 295 million people! These television adverts are also giving potential customers the chance to find out more about the product by using their websites to view and purchase. Something that wasnt available until a few years ago is changing the way we as the consumer purchase goods and as the company advertise it.

In able to get the best possible profit for your brand or product you need to make sure that first of all your product will sell, this sounds obvious but there is no point having a great advert for a poor product. Secondly making a decent profit between the hard cost and the RRP. The cherry on top is to make sure that you offer something that your competitors dont, giving them an incentive to buy your product.

You will find that once consumers use and enjoy your product they will more than likely purchase it again. A decent product will keep a customer for life.